Changing hard drive mac mini 2011

Articles

  1. Mac Mini Mid 2011 SSD Dual Drive Installation
  2. How to Change a Mac Mini Hard Drive | ihukokitivoj.tk
  3. Helpful answers
  4. All replies

Tighten the screws until they contact the end of the threaded holes in the side of the hard drive. They are shown correctly installed in the third picture. When inserting the hard drive, be sure to place it in its bracket cable side up with the SATA connector closest to the bulge in the bracket seen in the third picture.

Push the set screws into the grommets in the bracket and install the hard drive up into its bracket as seen in the second picture. Use a T6 Torx screwdriver to install the remaining two set screws through the grommets and into the side of the hard drive. Be sure that the mounting holes line up with the threaded holes in the outer case as seen in the second picture.

When the logic board is installed, simply connect the second hard drive cable to the free socket on the logic board. When you start up your machine, you'll see both drives are recognized by the Mini.

siva-group.eu/mujer-busca-chico.php

Mac Mini Mid 2011 SSD Dual Drive Installation

Xbench scores show that if you install hard drives in either the top or the bottom position, their speeds will remain the same. To minimize the amount of work necessary when adding an SSD to be used as your primary drive, we recommend installing the SSD like we did in this guide and leaving the stock platter drive in its original bottom position closest to the antenna plate.

Then install Lion on your SSD. Cancel: I did not complete this guide. Difficulty Moderate. Steps Time Required Suggest a time??

How to Change a Mac Mini Hard Drive | ihukokitivoj.tk

Sections 6. Flags 0. Step 1 Bottom Cover. Add a comment. Add Comment Cancel. Step 2. Step 3 Fan. Step 4. Pull the tool back towards you until the internals of the Mini separate slightly from the case. Pull the hard drive toward you and remove it from the case. Pull the connector off the drive, remove the two mounting pins from the side of the drive using a Torx T8 screwdriver and peel the plastic cover from the drive.

Replace the mounting pins on the side of the new drive, attach the connector and stick the plastic cover over the circuitry side of the drive. If you're replacing your drive with an SSD drive, you won't need the plastic cover. Push the drive back into position so that the mounting pins fit into the gaskets at the back of the drive bay, then reverse the steps to put your Mini back together.

Helpful answers

Connect your Mini, insert your bootable USB thumb drive and restart the computer. When you hear the startup chime, hold down the "Option" key to boot from the thumb drive and begin reinstalling Mac OS X on your new hard drive. Michael Cox writes about lifestyle issues, popular culture, sports and technology. In a career spanning more than 10 years, he has contributed to dozens of magazines, books and websites, including MSN.

All replies

Skip to main content. To remove the RAM, push the retaining clips on each side. When the top module pops up, slide it out and then slide out the bottom module. The Mac Mini has room for two hard drives, although it doesn't include mounting materials or connections for an additional drive. Because all of the hard drives use the same SATA-based interface , the process for changing out a drive, once you gain access to it, is pretty much the same. The SATA interface uses two connectors , one for power and the other for data.

The cables are small and easily maneuvered into position to make connections. You can't make the wrong connection since each connector is of a different size and won't accept anything but the proper cable.

There are also no jumpers to configure on SATA-based hard drives. This makes changing out a SATA-based hard drive a simple process. All Macs except the Mac Pro have temperature sensors attached to the hard drive. When you change out a drive, you need to reattach the temperature sensor to the new drive. The sensor is a tiny device attached to a separate cable. You can usually peel the sensor off the old drive, and just stick it back to the case of the new one. The exceptions are the late iMac and Mac mini, which use the hard drive's internal heat sensor.


  • free download google input tools for mac.
  • Macs with Hard Drives can Usually be Updated to Larger and Faster Drives.
  • 13 Answers.
  • telecharger des logiciels pour mac os x.
  • Installing an SSD in Mac Mini??

With these models, you need to replace the hard drive with one from the same manufacturer or purchase a new sensor cable to match the new drive. Having more storage space or a higher performing drive can make using your Mac much more fun, so grab a screwdriver and have at it.


  1. export outlook 2007 to mail mac;
  2. Add your answer?
  3. Replace HDD with SSD, will any SSD work (Mac Mini mid 2011)?.
  4. Puzzle solved: A faster Mac mini server.
  5. simcity 4 deluxe edition mac free.
  6. Share Pin Email. Tom Nelson has written hundreds of articles, tutorials, and reviews for Other World Computing and About. He is the president of Coyote Moon, Inc. The answer to the question of when to upgrade may seem simple enough: when you run out of space. Continue Reading.